Quick Answer: “Projector wall mount” covers two unrelated products, and buying the wrong one is the single most common mistake in this category. For a standard-throw home or classroom projector, the Mount-It! MI-608 (9”–29.5” extension, fits Epson/Optoma/BenQ/ViewSonic) is the right universal bracket. For an ultra-short-throw laser TV like Epson’s current QS100 4K PRO-UHD, you need a dedicated UST wall-mount arm instead — the Peerless-AV PSTK-028 or Chief WM110AUS, both rated to 50 lbs — or Epson’s own ELPMB75 ($207.00). And before buying any UST wall mount: Epson’s own support FAQ states an ALR screen “is not recommended” in the wall-mount configuration, which matters because ALR is the entire reason most people buy a UST projector in the first place.
A projector wall mount sounds like a smaller, cheaper version of a ceiling mount — the same bracket, aimed sideways instead of down. For a normal projector, that’s roughly true. For the ultra-short-throw laser TVs that now dominate projector marketing, it isn’t true at all, and the two products don’t overlap.
Corrected October 2026 — the Epson LS800 referenced throughout this guide is discontinued; its wall-mount info now applies to its current ELPMB75-compatible siblings, including its real successor, the Lifestudio Grand Plus (LS970). A prior version of this page wrongly named the LS650 as the LS800’s successor — it’s actually a separate, lower-tier sibling, and the finding that it can’t be wall- or ceiling-mounted per Epson’s own documentation stays true regardless of that correction.
By the numbers: Two figures define the split. Extension range runs in opposite directions: a standard-throw wall mount like the Mount-It! MI-608 extends the projector 9 to 29.5 inches out from the wall to cover a room-length throw, while a UST wall-mount arm like the Chief WM110AUS extends only 11.25 to 18 inches, because an ultra-short-throw lens fills the same screen from inches away. Weight capacity splits the same way: standard-throw brackets in this guide top out around 33 to 44 lbs, against home projectors weighing 7.9 to 28 lbs, while the two dedicated UST arms (Peerless-AV PSTK-028, Chief WM110AUS) are both rated to 50 lbs to cover heavier laser-TV chassis like the 19.8-lb Hisense PX3-PRO.
Best projector wall mounts at a glance
| Mount | Type | Capacity | Extension from wall | Price | Best for |
|---|---|---|---|---|---|
| Mount-It! MI-608 | Standard-throw | 33–35 lbs (spec disagrees by source) | 9"–29.5" | Varies by retailer | Most home/classroom projectors |
| VIVO MOUNT-VP06B | Standard-throw | 44 lbs (weight-tested) | 16.9"–25.6" | $29.99 | Budget universal pick |
| Peerless-AV PSTK-028 | UST/laser TV | 50 lbs | Up to 28", 6" lateral travel | Varies by retailer | Dual-stud UST installs |
| Chief WM110AUS | UST/laser TV | 50 lbs | 11.25"–18" | Varies by retailer | Single-stud, security locking |
| Epson ELPMB75 | UST/laser TV (first-party) | Not published | 100"–160" image size range | $207.00 (epson.com) | QS100/810E/Lifestudio owners wanting a guaranteed fit |
The thing no listing tells you: this search term covers two different products
Type “projector wall mount” into a search bar and the results mix two categories that have almost nothing in common except the word “wall.” The first is a standard-throw bracket — a small arm near the back-wall ceiling line that projects a normal-throw image most of the way across a room, the wall-mount cousin of the ceiling mounts covered in our best projector ceiling mount guide. The second is a UST (ultra-short-throw) wall-mount arm, which does something closer to the opposite job: it holds the projector a few inches off the floor, directly beneath the screen, standing in for the console or media cabinet the projector would otherwise sit on.
These aren’t different tiers of the same product — they’re built for opposite throw geometries. A standard-throw mount extending 9 to 29.5 inches (Mount-It! MI-608) would put a UST laser TV’s lens at completely the wrong distance and angle to fill its own screen; a UST arm extending only 11.25 to 18 inches (Chief WM110AUS) would leave a standard projector’s image a fraction of the size the room needs. Search volume for “projector wall mount” bundles both intents into one term, and most retail listings don’t say which type a product is until you read the fine print.
The Epson finding that should change your plan before you buy
Here’s the part that matters most if you own — or are about to buy — an Epson ultra-short-throw laser TV. Epson sells a wall mount for its UST line, the ELPMB75, which fits the current QS100 4K PRO-UHD, PowerLite 810E, and Lifestudio Grand Plus — plus the now-discontinued LS800, if you already own one. Epson’s own support FAQ, answering “Can I mount my LS800 to a wall?”, confirms the mount exists and then adds this:
“An ALR screen is not recommended with the wall mount configuration; a traditional white screen can be used.”
That carries over to every ELPMB75-compatible model, current or discontinued: these projectors typically ship bundled with Epson’s own ALR (ambient-light-rejecting) screen, and ALR is the specific technology that lets a UST laser TV throw a watchable picture in a normal, lit living room instead of a blacked-out home theater. Wall-mounting the projector — per Epson’s own instructions — means switching to a traditional white screen, which gives up the exact capability that separates a $2,000+ UST laser TV from a cheaper standard projector.
There’s a second, newer wrinkle worth knowing before you shop. Epson’s LS650 — a separate, lower-tier UST model, not the LS800’s successor despite the similar name — dropped wall/ceiling mounting entirely: Epson’s own LS650 user guide states the projector “is not intended to be ceiling- or wall-mounted,” full stop, with no ELPMB75-style accessory offered for it. The LS800’s actual successor, the Lifestudio Grand Plus (LS970), is already on the ELPMB75’s compatible-model list above. So if you’re comparison-shopping Epson USTs by model name rather than by checking each one’s own documentation, don’t assume wall-mountability carries forward consistently across the lineup — it varies model by model.
This isn’t a defect or a mistake in the mount. For the models that do support it, it’s a geometry constraint: an ALR screen’s lenticular layer is engineered to accept light arriving from the narrow, specific throw angle a UST projector produces when it sits on a console at the correct height and distance below the screen. Change that geometry — which a wall mount does, by design, since it repositions the projector relative to where a console would put it — and the screen’s light-rejecting structure is calibrated for the wrong angle. Before buying any UST wall mount, decide whether you’re prepared to run a plain white screen instead of ALR, because for Epson’s own current lineup, that trade is explicit and documented, not a rumor from a forum thread.
Our picks
Best overall (standard-throw) — Mount-It! MI-608
Mount-It! MI-608 — Best wall mount for standard-throw projectors
- The widest extension range in this guide for a standard-throw projector — covers everything from a shallow alcove to a near-room-length throw.
- Universal bracket compatible with the major home and classroom projector brands, not a single-model mount.
- Worth flagging: Mount-It!'s own listings disagree on capacity — Amazon's product title states 35 lbs, while Mount-It!'s product-page URL slug states 33 lbs. Either figure clears a typical 7.9–9 lb home projector many times over, so the discrepancy doesn't change the buying decision, but don't cite one number as gospel.
- This is a standard-throw bracket, not a UST arm — see the picks below if your projector is a laser TV.
A projector needs something to play — Prime includes Prime Video. Try it free for 30 days.
Best budget pick — VIVO MOUNT-VP06B
VIVO MOUNT-VP06B — Best budget wall/ceiling projector mount
- Cheapest mount in this guide by a wide margin, and rated well above what a typical home projector weighs.
- Works as either a wall or ceiling mount, so it's a reasonable pick if you haven't committed to one installation yet.
- 8.9"–12.4" hole span is narrower than some home-theater chassis — measure your projector's mounting points before ordering, the same caution that applies to VIVO's ceiling mounts.
Best UST/laser TV arm — Peerless-AV PSTK-028
Peerless-AV PSTK-028 — Best dual-stud UST wall-mount arm
- 50 lb capacity comfortably covers heavier laser-TV chassis, such as the 19.8-lb Hisense PX3-PRO.
- 6 inches of lateral travel gives fine left-right centering under the screen without redrilling.
- Security screws pre-installed on the arm — a detail aimed at classroom and public-space installs, same audience as Chief's WM110AUS below.
- Peerless-AV does not publish a direct list price; compare current pricing across retailers before buying.
Best single-stud UST arm — Chief WM110AUS
Chief WM110AUS — Best single-stud UST wall-mount kit
- Single-stud installation, simpler than the PSTK-028's dual-stud plate where wall framing doesn't line up for two studs.
- Quick-connect system with micro height/leveling adjustment, aimed at fast professional installs.
- Four keyed-locking options make this the pick for shared or public installs where tamper resistance matters, echoing Chief's ceiling-mount lineup.
- Chief does not publish a direct list price either; check current retailer pricing before buying.
First-party option — Epson ELPMB75
Epson ELPMB75 Extreme Short Throw Wall Mount
- The only mount in this guide guaranteed to match an Epson UST's screw pattern, since it's Epson's own part.
- Read this before buying: Epson's own FAQ states an ALR screen "is not recommended" with this wall-mount configuration — pair it with a traditional white screen instead, not the ALR screen these projectors typically ship bundled with.
- Compatibility is narrow by design — four named models only, unlike the universal UST arms above. Notably absent: the LS650, a separate lower-tier sibling model (not the LS800's successor) that Epson's documentation says isn't wall- or ceiling-mountable at all.
How to buy: the two-minute sort
| Step | What to check | Where the number comes from |
|---|---|---|
| 1. Projector type | Standard-throw or UST/laser TV — this decides the entire product category | Your projector's spec sheet (throw ratio) |
| 2. Screen type | If UST, are you keeping the ALR screen or switching to white | Manufacturer FAQ — Epson's says ALR is not recommended wall-mounted |
| 3. Stud layout | Single-stud (Chief WM110AUS) vs double-stud (Peerless PSTK-028) wall plates | Stud finder before you shop, not after |
| 4. Hole span / screw pattern | Measure your projector's mounting points, compare to the mount's range | Tape measure, same caution as our ceiling mount guide |
| 5. Capacity | Last, not first — every mount here clears a typical projector's weight | Manufacturer spec sheet |
The bottom line
Figure out which category you’re shopping in before you look at a single listing. If it’s a standard home or classroom projector, the Mount-It! MI-608 covers the widest extension range for the money, and the VIVO MOUNT-VP06B is the cheaper universal alternative. If it’s an ultra-short-throw laser TV, skip standard-throw brackets entirely and go to the Peerless-AV PSTK-028 or Chief WM110AUS — or Epson’s own ELPMB75 if you own a compatible Epson model (QS100 4K PRO-UHD, PowerLite 810E, Lifestudio Grand Plus, or a legacy LS800) and want a guaranteed-fit first-party part. If you’re shopping Epson’s LS650 instead — a separate, lower-tier UST model, not the LS800’s successor — skip wall mounts entirely: Epson’s own documentation says it isn’t rated for wall or ceiling mounting. Either way, decide on your screen first: Epson’s own guidance is that a UST wall mount pairs with a traditional white screen, not the ALR screen most laser TVs are bought for. If a console setup still works in your room, our best projector stand guide covers the rolling-cart and tripod options that keep the ALR screen fully compatible. And once anything is on the wall, our best HDMI cable for projector guide covers the cable-run question a wall install always raises, while our projector throw distance calculator confirms exactly how far your specific model needs to sit from the screen before you commit to a mount.